Richard Hanger

How to Clean Rusty Model Train Track

railway club 4

How to Clean Rusty Model Train Track

How to clean rusty model train track is a common question for many model railway enthusiasts. It can be a difficult task, but there are some techniques that can be helpful. A few of them are Dremel, White vinegar, Oils and EvapoRust. This article will outline some of these methods and help you determine which one is best for your particular model. Once you have identified the problem, you can begin the cleaning process.


How do you clean rusty model train track? First, you need to make sure that the track is completely rusted before you start the cleaning process. You can use a baking soda and water solution or vinegar wash. Both of these solutions will help you remove the rust and dirt from the track, but they have limited effectiveness. A good option is to purchase a container of EvapoRust and soak the track in it for a few minutes. This solution is a great solution to remove the rust on your track, but you should be sure to follow the instructions on the bottle.

After thoroughly cleaning the rusted track, drain the tank and inspect the rust with an LED torch. If the rust is heavy, you may need to wash out the track with clean water. Never use cleaning solutions to clean the track, as they can reduce the effectiveness of the Evapo-Rust solution. Then, apply the solution to one side of the tank and let it sit for two to three hours before washing it.


The Dremel is a great tool for model railroaders, but there are several things you should never use it for. One example is using it to clean rusty model train track. While this is not a very serious problem, a hobbyist may accidentally damage his or her track. The following tips will help you avoid making a big mess while cleaning your track. You should use a carbon steel brush to clean the rust off the rails.

The most effective way to clean rusty model train track is to use specialized chemicals. These chemicals dissolve corrosion and dirt without rubbing or grinding. These cleaners are available at hobby stores and are generally safe. They should evaporate quickly and not damage the rolling stock or scenery. A wire brush can also work very well. This method may be a bit more time-consuming, but the end result is worth the effort.

White vinegar

A white vinegar bath can be an excellent way to remove rust from model train track. It will also remove any plating that is present. If a part is completely rusted, there is no plating remaining. However, if the rust is on the interior of the track, there may be some plating in the corroded area. To remove plating from a track, use a scourer made of stainless steel.

If the rust is severe, you can also use a rust remover spray to treat individual rust spots. Then, run the track through a dishwasher to remove any excess water. After rinsing, make sure to dry the track to prevent further rusting. You can even automate this process by using a cleaning car. If you can manage to remove all the rust, you can clean the cars.


When you’ve got a rusty model train track, you might not think that you can do much to clean it. However, a few simple steps can make it look like new again. First, you should avoid using hot water and soap for cleaning the track. While this method works for cleaning a rusty track, it also tends to worsen the rust problem. It can even cause rust to develop on freshly cleaned surfaces.

First, you can use WD-40 to clean the surface of rust. You can also use Liquid Wrench to clean the railings. These will work well to slow down the rusting process and make it look like new again. Once you’ve cleaned the surface, you can use oil to repair the railings and lubricate them. You can also use them to prevent the rust from spreading to the track’s railings.

Non-polar solvents

You can use non-polar solvents to clean rusty and dirty model train track. These solvents are non-explosive and have low electrical attraction, so they are less likely to bond with the rails. They are also non-toxic and do not leave harmful residue. Non-polar solvents are effective at cleaning the track and reducing the frequency of cleaning. The following are some of the non-polar solvents you can use.

Water-based solvents. While water-based cleaners can clean the surfaces of metals, they leave behind residues and encourage the buildup of metal oxides on the track. Water-based solvents can also damage pivot areas and rail joiners, which may cause them to corrode over time. This is why it is best to use non-polar solvents for cleaning rusty model train track.